Processing Image File :
rm827__03.04.ppm_m1
[]: Found 1 active devices.
[Nokia C2-00 USB Phonet]: Opening Connection
[Nokia C2-00 USB Phonet]: Port opened OK!
SW: V 03.04 20-04-12 RM-827 (c) Nokia
IMEI: 353259059973243
START FULL PM BACKUP
Please Wait...
Reading : PM 0~400... OK!
FULL PM Backup Saved to:
C:AdvanceBox Turbo FlasherNokiaBackup353259059973243USB_FULL_BACK UP_V 03.04 20-04-12 RM-827 (c) Nokia_353259059973243__111106.pm
Reading Battery Value : 4974 mV
Rebooting Phone...
AUTO SELECTED DEAD USB FLASHING...
If Phone Booting does not Start in 5 Seconds,
Then Perform Steps 1, 2, 3 and 4...
1. Remove USB and Battery...
2. Insert USB.
3. Insert Battery. (Some phones boot automatically)
4. Please Power on phone shortly...
Infineon USB Boot: F00A1FB300020303010100FF
Sending PBL...
PBL Successfully Sent...
Sending SBL...
SBL Successfully Sent...
Setting Transmission Speed Done...
Flash Chip Manufacturer: Intel Electronics Corp.
Flash Boot Successful...
Sections : 01
Current File : rm827__03.04.ppm_m1
Compile Name: package_m1.ppm_ebl_psi.fls
Image Type : PPM Image
Data Size : 4062644 Bytes
Sending Certificate Block
PPM Certificate Block Sent Successfully...
Processing Section 01 of 01
PPM Erase Block: 0x41BC0000~0x421BFFFE
Start Erasing...
Erasing Please Wait...
Block Erase Done...
Preparing Data Blocks...
Data Size: 4059300 bytes
Data Checksum: D696
Uploading Data Blocks to phone...
Block Write Successful...
PPM Data Blocks uploaded to phone...
Data Verification Successful...
Total Flashing Time (Erase + Flashing) : 00:00:39
(Booting time is NOT Included)
Waiting for Phone to Start-Up..(Max 150 seconds)
FACTORY SET TO : Full Factory Set
OK
FACTORY SET TO : User Data
OK
FACTORY SET TO : Leave Factory
OK
FACTORY SET TO : Service Center
OK
FACTORY SET TO : Software Upgrade
OK
FACTORY SET TO : Production Tune
OK
RESET LIFE TIMER TO : 0000:00
OK
when we plugin charging pin into charging jack of Nokia 110 and it do not shows any thing it can be fault of missing track or parts in it and can be fault of charging base.While if it shows not charging then it can be reason of water damages or low volt.so here is a diagram to help you to understand charging parts and there tracks.
look at above diagram and clean all these parts which are given in it.clean all these parts and apply hot air to dry the board.Check these parts with meter and if path is missing apply jumpers as given in above diagram solution.to Fix charging problem you can replace charging base also.Red line shows positive track of charging function while blue is a ground print.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
to get new repairing cellphone diagrams and applications with email “Enter your email address for RSS:” at the right side at top and press “subscribe”
How to Use Nokia Flash Tool. Step 1) First, install the ADB & Fastboot drivers on your PC. Step 2) Charge your phone to at least 50%. Step 3) Download the Firmware for your phone and extract it on your computer. Step 4) Double click on the Nokia flashing.exe to run the Nokia flash tool. Step 5) Power off your Nokia phone. Jun 19, 2018 Nokia 110 (RM-827) V3.47 MCU,PPM,CNT Flash file & USB Pinout 100% Tasted By Ma Mobile Without Password June 19, 2018 Symphony I-70 FRP Remove File One Click With SP Flash Tool 100% Tasted By MA Telicom Without Password.
Nokia 110 Pinout
- Nokia 112 And 110 New Usb Pinout. Nokia X1-01 Full Pinout. Nokia 500 RM-750 Full FBUS Cable Pinout. Leave a Reply Cancel reply.
- Nokia 110 Flash File (RM-827) V3.48 update version is a free and useful tool for Nokia device. If you feel the necessity of flashing and do not want to go to market, you can use this tool to do it yourself. The latest version comes with some unique features. However, with this software, you can Nokia 110 Flash File (RM-827) V3.48 100% Tested Download Read More ».